[0-9]
8001 Diagnosis acknowledgement
8002 Controller boot started
8003 Controller boot finished
8005 Program automatic start active
8013 Controller connect to TCP/IP server
8014 Controller disconnect from TCP/IP server
8020 Program cycle check has changed
8021 Program cycle check values are changed
8022 FC_SetTaskPriority() called
8030 UPS active - no power
8032 UPS begin saving retain area
8033 UPS retain area saved
8034 UPS program tasks terminated
8035 UPS active - system shutdown started
8036 UPS controller rebooting started
8038 NvRam/RTC power fail detected
8042 Sercos phase switched
8043 Sercos detect configuration
8045 File write error detected
8046 FPGA firmware download
8047 PIC firmware download
8048 BT-4 firmware download
8053 UPS active overtemperature
8054 Controller temperature out of range
8055 Controller message HW monitor
8056 Controller power supply low
8057 Program online change
8059 UPS active - IEC-control task running
8064 TM5 I/O data length exceeded
8065 TM5 cycle time not valid
8091 Software error (unknown exception)
8101 Power stage overtemperature
8102 Motor overtemperature
8104 Control voltage out of range
8105 Encoder position invalid
8106 DC bus contr.communication not possible
8111 Shutdown due to tracking deviation
8112 Sercos telegram invalid
8113 Shutdown due to deviation of estimated position
8114 Device type plate not readable
8116 Commutation error detected
8117 Motor type plate not readable
8119 Power stage short-circuit / ground fault
8120 Power stage overload
8122 Shutdown due to velocity limit
8123 Safe Torque Off incorrect
8126 Power stage temperature high
8127 Motor temperature high
8129 Power stage load high
8132 Tracking deviation limit exceeded
8133 Speed-dependent current reduction
8134 External 24 VDC too low
8136 Safe Torque Off active
8138 Motor/Drive combination not supported
8139 DC bus precharge not possible
8140 Motor StopTimeLim exceeded
8142 Control board overtemperature
8143 Encoder temperature high
8144 DC bus short-circuit / ground fault
8153 DC bus discharge not possible
8161 Control board temperature high
8163 Sercos Slave C1D error detected
8164 Sercos C1D man.-specific error detected
8165 Sercos Slave C2D warning detected
8166 Sercos C2Dman.specific warning detected
8169 Sercos Slave comm. disturbance detected
8170 Encoder position not accessible
8171 Encoder comm. disturbance detected
8174 Incremental encoder output is not working
8175 Extended message for encoder disturbances
8176 Encoder connection break
8177 Power board overtemperature
8179 Braking resistor load high
8180 Power board temperature high
8182 External 24 VDC power supply high
8183 Device fallback firmware active
8184 HW/SW combination not supported
8185 Device error detected
8187 Option module not supported
8188 Function not supported by Hardware
8189 Safety module communication not possible
8190 Current control parameter reduced
8191 Mechanical overload protection
8193 Machine encoder temperature is high
8194 Machine encoder position is not accessible
8195 Machine encoder signal is out of range
8196 Machine encoder communication disturbance detected
8197 Machine encoder type plate is not readable
8198 Machine encoder is not supported
8199 Deviating encoder feedback
8200 Faulty logical address of parameter (class 3)
8202 Faulty configuration file
8204 Program cannot be loaded
8205 Impermissible parameter value
8250 Firewall error detected
8252 Firewall deactivated
8253 Firewall configuration file not found
8254 Firewall configuration file error detected
8255 Firewall applied default rules
8256 Firewall configuration file loaded
8257 Firewall configuration file created
8300 Program divide by zero
8301 Coprocessor segment overflow
8303 General protection error
8305 Memory limit exceeded
8307 Double execution error
8308 Invalid task state segment
8310 Faulty memory segment adjustment
8311 Coprocessor division error
8312 Parameter relocation failed
8313 Excessive cycle time overrun
8316 NvRam data not valid
8317 Program cycle time overrun
8318 Program calculated profile deleted
8320 Bad array access (check)
8321 Division by zero (check)
8322 Exception by IEC task
8324 UPS failure detected
8326 Program function not supported
8327 CamTrack invalid PositionSource
8328 CamTrack invalid Destination
8329 CamTrack invalid Bitnumber
8330 Program master job not executable
8333 EncoderNet receiving data not possible
8334 EncoderNet receiving data dist.detected
8335 EncoderNet synchronization not possible
8336 EncoderNet Sync. disturbance detected
8337 Parameter DynIECData value too high
8338 UPS battery not charged
8339 UPS active - system temperature high
8340 Out of range (check)
8341 CamTrack invalid Position type
8342 On/OffPos inverted (Is On/OffDelay ok)
8400 Program diagnostic message class 0
8401 Program diagnostic message class 1
8402 Program diagnostic message class 2
8403 Program diagnostic message class 3
8404 Program diagnostic message class 4
8501 Sercos slave not found
8503 SERCOS service channel error detected
8504 Sercos read cycle overflow
8505 Sercos Master comm.disturbance detected
8506 Sercos Master comm. not possible
8507 Sercos write cycle overflow
8508 Sercos run-up not possible
8509 Sercos slave SW not supported
8510 Sercos Interrupt lost
8512 Sercos wrong device type
8517 Sercos addressing not unique
8518 Sercos too many real slaves
8519 Sercos connection configuration
8520 Sercos C2C misconfiguration detected
8521 Sercos C2C configuration
8522 C2C encoder error detected
8524 Slave comm. disturbance detected
8525 C2C Slave comm. error detected
8526 C2C Slave critical error
8527 C2C Slave error detected
8529 Sercos Slave C1D error detected
8530 Sercos Slave C2D warning detected
8532 Sercos Logical Slave not unique
8533 SERCOS Slave unresponsive
8550 Cybersecurity device lock status
8551 Uncontrolled carrier received
8553 Segment power consumption near limit
8555 Carrier moved beyond track end
8560 Power stage hardware error detected
8561 Segment to segment connection error detected
8562 Carrier negotiation communication error detected
8563 Encoder error detected
8565 Track is not the first Sercos device on the LMC
8566 LMC connected to the incorrect port of the track
8567 Segment coil overload
8568 Segment coil load is high
8571 Logical Carrier not unique
8572 Physical Carrier not unique
8573 Wrong Segment Geometry
8574 Unconfigured physical carrier found
8600 Master Encoder comm. not possible
8601 Master Encoder signal out of range
8723 No profibus config data
8725 Firmware of the module was replaced
8726 Firmware of the module is incorrect
8730 Bad master parameter data
8731 Automatic bus deactivation
8732 Slave not responding
8740 Device cannot be disabled
8780 Encoder output frequence > 1MHz
8781 Master Encoder no connection
8782 Master Encoder signal out of range
8785 Hardware defect detected
8786 Asynchronous to Sercos bus
8788 Wiring error detected
8789 PacNet comm. disturbance detected
8790 Module error detected
8791 TM5/TM7 module error detected
8792 SoSafe configuration mismatch
8793 Safety device firmware incompatible with SLC type
8794 Safety device firmware incompatible with SLC type
8800 Insufficient working memory
8826 PIC update not possible
8827 Controller power-off/hardware monitor
8829 Velocity too high for ZeroTrack
8830 PacNet BusAddr duplicated
8902 Software error (page fault)
8903 Software error detected (class 3)
8904 Software error detected (class 4)
8905 FC_UserRefGeneratorStart not possible
8907 Encoder interface invalid
8908 Unintended motor operation detected
8909 Motor type plate parameter invalid
8910 Reference value invalid
8915 Selected EncoderMode not supported
8916 Wrong ControlMode selected
8917 Machine encoder interface is invalid
8918 Machine encoder communication is not possible
8919 Machine encoder type plate parameter is invalid
8957 Sercos bus topology changed
8958 Encoder communication not possible
8959 Mains contactor error detected
8960 Invalid mains voltage mode setting
8961 Phase missing message
8963 NRT IPAddr not in IPAddressRangeStatic
8964 NRT IPAddressRangeDynamic used up
8965 NRT IP parameter read not possible
8966 NRT IP parameter write not possible
8967 NRT IP parameter device different
8968 NRT network overlapping detected
8969 Motor cable not connected
8970 Fast Device Replacement
8971 Fast Device Replacement not successful
8972 Gateway not in network
8974 Brake voltage too low
8975 Motor commutation invalid
8976 Mains phases wiring not correct
8977 Motor temp. monitoring disabled
8978 InverterEnableConfig invalid
8979 STO_A and STO_B different levels
8980 Braking resistor not connected
8983 DC bus precharge active
8984 DC bus precharge complete
8990 Firmware update not possible
8991 Data transfer invalid
8992 Braking resistor short circuit
8993 Last device on Sercos port
8994 Invalid ProducerCycleTime
8995 Update motor type plate
8996 Update motor type plate not successful
8997 Parameter MotorIdentification invalid
8998 TM5/TM7 Supply voltage too low
8999 TM5/TM7 Warning supply voltage